How to Solder Wires Together || Step by Step

How to Solder Wires Together || Step by Step

How to Solder Wires Together || Step by Step

Solder Soldering Station Tin Board Electronics

Soldering is a procedure wherein at least two metal parts are combined by dissolving a filler metal, otherwise called patch, to join the segments. Bind normally has a lower liquefying point than both of the metal segments being joined. These directions will walk you through the means of soldering wires together in a sheltered and productive way. Soldering can be risky. You should utilize hot and sharp articles so make certain to peruse all alerts. 



Score or make a slight cut on the wire coat. You need to make the score about ½" from the finish of each wire that will be bound. To do this, you can utilize a couple of wire strippers or an extremely sharp edge. Be cautious, you would prefer not to cut the real copper wire as it will detract from its leading quality. 


  • Decide the span of the wire and utilize the fitting estimated gap to appropriately strip the wire. In the event that you don't have the foggiest idea about the extent of the wire, try out the gaps in the strippers to locate the one that cuts into the coat without cutting the wire. 
  • Cinch down on the wire with the privilege measured the opening. Presently you will turn the wire 90 degrees in the pivot and do something very similar. Do this a couple more occasions with the goal that you have a decent line around the entire wire coat. On the off chance that you are simply utilizing a disposable cutter, remember to make the entry point around the entire periphery of the coat. 



Force the undesirable coat off. When you have that slight cut in the coat, you ought to have the option to twist the coat forward and backward until the coat comes free. You can do this with the strippers or with your fingers. In the event that it doesn't come free immediately take a stab at making the somewhat more profound cut into the coat. The thought is to get the bit of coat off without giving up any 



Cut a bit of psychologist cylinder and slide it onto one of the wires (If you are utilizing electrical tape to cover your joint, avoid this progression). In the event that you are utilizing the therapist cylinder to cover your association, you will need to slide the psychologist tube onto the wire before interfacing the wires. The bit of therapist cylinder ought to be longer than the zone being bound. 


  • The therapist cylinder should cover a portion of the coat on each end and the ½" association you are making. Utilize your scissors to cut a 1-1 ½" bit of therapist. You may test the therapist tube on a bit of the wire before beginning to ensure the tubing will psychologist down to the extent of the wire. Most psychologist cylinders lessen to around 1/3 of its size in the wake of being warmed. 


Excoriate both ½" bits of copper wire. To make a decent association between the copper wires, you will need however much of the wires contacting each other as could reasonably be expected. Commonly, the most ideal approach to do this is to excoriate each finish of the wire out. Do this by scouring the wire between your fingers. The wires should now resemble this. 



Push the excoriated closures into one another. The copper wires ought to be somewhat interwoven with one another. Curve and smooth the strands into one another so they hold together. The objective is to make the strands of copper from the two separate wires appear as though one. Ensure the region is smooth. This is the territory that you will bind. On the off chance that it is excessively massive, you will most likely be unable to fit the psychologist over the joint. 



Add the weld transition to the association. You can utilize your finger or a utensil to do this. Try not to be unassuming with the motion, however, don't squander it either. You can generally include all the later. The transition will help the weld stream into the wires so the more you have on the association, the simpler your soldering occupation will be. Begin with a little glob on your finger or utensil and brush it onto the wires. The following stage will include warming the wire which will douse up this transition. 



Warmth the motion into the wires. Utilize your warmth weapon or blow dryer, expecting your blow dryer creates enough warmth, to liquefy the transition. Don't simply point the warmth source at the wires. You will need to wave the warmth source forward and backward so there isn't as much direct warmth on the wires. Overheating the coat may make it soften. Be cautious, you don't need the therapist cylinder to get any warmth yet, so ensure the psychologist cylinder is a long way from the territory you are applying the warmth. 



Append the correct tip to the iron. (In the event that you have the right tip on the iron in the first place, skirt this progression) A tip that is too little won't move enough warmth to bigger wires. A tip that is too enormous may apply an excessive amount of warmth and dissolve the coat on the wire. The thought is to utilize a tip that applies simply enough warmth for the venture. Most media measured tips will work for soldering wire. 


  • Try not to contact anyplace over the handle of the iron. Iron tips can be connected by screwing off the barrel appeared. Continuously ensure the iron is off before supplanting tips. In the event that supplanting the tip while the iron is on, metal connected to the soldering iron will be hot; so use alert! 




Turn on the bound box. It is critical to keep the weld box and iron in a protected territory. You should possibly turn the iron on when you are prepared to utilize it. Ward off combustible articles from the iron consistently. Make sure to kill the container when you are finished utilizing it. Add water to the wipe beneath the soldering iron holder. This wipe can be utilized to clean the tip of your iron. 



10 Get some bind with the iron. Lifting the weld up with the iron is least demanding for littler wires. You can do this by contacting the tip of the iron about an inch from the finish of the string of weld. The iron ought to naturally drench the patch right onto the tip of your iron. This enables you to concentrate exclusively on the iron as opposed to holding the bind in your other hand. In the event that the iron is hot enough, the bind should stream right onto the copper when you contact the iron to it. Diverse estimated wires will require various measures of a bind. 



11 Apply the iron with the patch to the copper wire with motion. With the bind as of now on the iron, you should simply contact it to the copper wires. The motion that was warmed into the wires will make the patch stream directly into the association. In the event that it doesn't stream effectively you may need to add more transition to the wires. Rehash your past procedure and attempt. Once more, you would prefer not to leave the warmth source, the soldering iron for this situation, in any spot for a really long time. You ought to easily wave the iron forward and backward along with the copper. Keep on grabbing progressively bind with the iron and add it to the joint until the wires are full. 


12 Investigate the joint. The wires should now be completely joined. See all sides of the association. Now and then if the weld doesn't stream appropriately, the posterior of the association might not have enough patch to appropriately join the wire bringing about a frail association. A slight pull on the wires can be utilized to guarantee a decent tie. 



13 Spread the joint. Spread the fastened association with your therapist cylinder or electrical tape. Slide the therapist tube over the joint and apply warmth to the territory similarly you did with the warmth weapon, by waving the warmth source forward and backward so there is less immediate warmth on the coat. On the off chance that you have neglected to put the psychologist tube on the wires, you may dependably utilize electrical tape to cover the zone; shrivel tube just functions admirably by and large as it looks cleaner and doesn't leave a cement buildup. 

Alerts / Warning


  • Soldering irons ordinarily have a tip temperature somewhere in the range of 600 and 800 degrees Fahrenheit. 
  • Be cautious when taking care of any sharp or hot article. 
  • Cautiously return the iron to its holder at whatever point it isn't being used. 
  • Weld in the well-ventilated zone. Vapor can be dangerous. 
  • Try not to take a shot at live electrical wires.
Tags: how to solder wires, how to solder wires together, how to solder two wires together, how to solder wires to a circuit board, how to solder small wires,how to solder wires to connectors, how to solder headphone wires, how to solder two wires,how to solder wires to terminals.